The Cisco ASR X Router offers embedded services for enterprise and service provider networks in a 2-rack unit (2RU) small form factor. It is integrated with. ASR X Router: Access product specifications, documents, downloads, Visio stencils, product images, and community content. Data sheet describes how the Cisco SPA/SIP portfolio offers a rich set of QoS features for premium service delivery.
|Published (Last):||23 January 2007|
|PDF File Size:||12.12 Mb|
|ePub File Size:||9.95 Mb|
|Price:||Free* [*Free Regsitration Required]|
It can be configured with your choice of a 5-gigabyte per second or a gigabyte per second embedded services processor.
Certain services require only a right-to-use RTU license, whereas other services require both an RTU license and one or more number-of-sessions licenses.
Datasheer on the Cisco QuantumFlow Processor, the ESP performs forwarding, network security, deep packet inspection, firewalling, data center interconnect, and many other advanced features.
If an entire virtual device fails, Cloud VPN automatically instantiates a new one with the same configuration, so you don’t need to build two Cloud VPN gateways. Select the gateway’s entire subnet in the pull-down menu. satasheet
GCP does ECMP by default so there is no additional configuration required apart from creating x number of tunnels where x depends on your throughput requirements. ELCs come in two different types: If a Cloud VPN tunnel goes down, it restarts automatically. A two-rack unit, the Cisco ASR is a router that has both serial interface processors and an integrated route.
Name — The name of the Cloud Router. There are all kinds of news and information related to Cisco and Cisco network equipment, such as release of Cisco equipment, news of Cisco’s new networking solution, and Cisco hardware and software upgrading The new gateway and tunnel connect automatically. To ensure symmetry in your traffic flow, you can configure MED to influence the inbound traffic from GCP for the same tunnel you are sending outbound traffic to.
It has a feature called DPI, which filters packets in the computer network to search for spam, viruses, intruders, and other security issues. This comprison show you the models.
Cisco ASR Router Datasheet and Installation
Peer IP address — Enter your on-premises public IP address here, with the above mentioned topology it is Although you must make a selection, your choice of application part number has no effect on the Cisco ASR Series Routers.
Cisco ASR Router. Both of these Ethernet line cards have built-in SIP. The region must be the same as for the tunnel. In this block, the following parameters are set Perfect Forward Secrecy PFS – PFS ensures that the same key will not be generated again, so forces a new diffie-hellman key exchange.
Note that lower the MED, higher the preference. This information is provided as an example only. DPD — set the dead peer detection interval and retry interval, if there are no response from the peer, the SA created for that peer is deleted. These negotiations involve two phases: All traffic routed to the tunnel interface will be encrypted and transmitted to the GCP. Click Create VPN connection.
A transform set represents a certain combination of security protocols and algorithms.
It can be any private ASN you are not already using. BGP timers are adjusted to provide more rapid detection of outages.
SA Fatasheet – set the lifetime of the security associations after which a reconnection will occur. Saving the configuration To save the running configuration and set it as the default startup, run the following command on Cisco IOS terminal: Remote network IP range — Actually, you may be strange to the ASR Series because these routers always work for a carrier or service provider or a very large enterprise. This guide is not meant to be a comprehensive setup overview for the device referenced, but rather is only intended to assist in the creation of IPsec connectivity to Google Cloud Platform GCP VPC networks.
The Cisco ASR only sips power and takes up little rack space, thanks to the fact that the router has been designed in as a compact form factor device.
It must belong to same subnet as the GCP-side interface. Association with the IPsec security association is done through the tunnel protection command.
You can repeat this command to add multiple ranges to the VPN daatasheet. Normally, this is the region that contains the instances you wish to reach.
What is an ASR Router? If you don’t have a static external IP address, you can create one by clicking New static IP address in the pull-down menu. For details, see our Site Policies.
Local subnets — Specifies which IP ranges will be routed through the tunnel. Or, you can leave it blank since the local subnet is the default.