Site Loader

Mazda6. Workshop. Manual. FOREWORD. This manual contains on-vehicle service and diagnosis for the Mazda6. For proper repair and maintenance. Brochure Mazda 6 (GH..> , K. Engine Workshop Manu..> M6-engines-manual-bo..> , M. MAZDA 6 REPAIR MANUAL File ID: – File Type: PDF File Size MAZDA 6 REPAIR MANUAL — The following PDF file discuss about.

Author: Nigar Murr
Country: Japan
Language: English (Spanish)
Genre: Sex
Published (Last): 22 October 2004
Pages: 226
PDF File Size: 15.24 Mb
ePub File Size: 10.42 Mb
ISBN: 917-1-55401-802-5
Downloads: 71057
Price: Free* [*Free Regsitration Required]
Uploader: Goltigul

As modifications affecting repair or Automatic Transaxle maintenance occur, relevant information JA5AX—EL supplementary to this volume will be made available at Mazda dealers. This manual Propeller Shaft should be kept up-to-date.

The contents of this manual, including drawings and specifications, are the latest available at the time of printing, and Mazda Motor Corporation reserves the right to change the vehicle designs and alter the contents of this manual without notice and without incurring obligation.

Therefore it may not contain the necessary reference service procedures to perform the service indicated in this manual.

End Of Sie GI— In some models, there is a fuel pump relay that controls pump speed. That relay is now called the fuel pump relay speed.

Device that controls engine and powertrain 5: Directly connected to exhaust manifold 6: All inspections and adjustments must be made by an expert repairer, we recommend an Authorized Mazda Repairer.

Brake fluid Replace brake fluid. If the voltage from accelerator pedal position sensor No. The PCM calculates the deviation of the interval time for each cylinder. If the deviation of interval time exceeds the preprogrammed criteria, the PCM detects a misfire in the corresponding cylinder. If the glow relay voltage is 4. Always carry out a total inspection of the input systems, output 2009, and PCM to determine the cause of trouble. Verify that the voltage at terminal B changes while applying the vacuum to the EGR valve as show in the graph.

Perform the necessary vehicle preparation and visual inspection. If the fuel pressure is lower after the fuel injection than the preprogrammed criteria, the PCM determines fuel system leakage.

Mazda 6 Service Repair Manual PDF

If the difference between the maximum and minimum value of the intake air temperature sensor No. If manuual voltage characteristic of the air flow sensor signal is out of the threshold, the PCM determines that there 2090 a malfunction in the mass air flow sensor.

If the difference of the vacuum inside the intake manifold during middle engine speed and low engine speed is less than the threshold, the PCM determines that there is a malfunction in the manifold absolute pressure sensor characteristic.

  1S2473 DATASHEET PDF

If the voltage from the manifold absolute pressure sensor is more than 4. If the voltage from the engine coolant temperature sensor is less than 0.

MAZDA 6 WORKSHOP MANUAL Pdf Download.

If the voltage from the fuel temperature sensor is less than 0. If the voltage from the fuel temperature sensor is more than 4. If the PCM does not receive the injection confirmation signal for unspecified cylinder normally, the PCM determines that the unspecified cylinder fuel injector operation is mazd verified.

Go to the next step.

If the idle switch is off even if the voltage from the accelerator pedal position sensor is less than 0. Yes Inspect suspected circuit or part or both according to the inspection results. If the EGR solenoid valve vacuum voltage is low even if the EGR solenoid valve vacuum is off, the PCM determines that there is a malfunction in the intake shutter solenoid valve control circuit.

If the PCM detects the circuit current is less than 1 A when the suction control valve is on, the PCM determines that there is a malfunction in the suction control valve circuit. If the PCM detects circuit current is more than 1 A when the suction control valve is off, the PCM determines that there is the malfunction in the suction control valve circuit. If the intake shutter solenoid valve half voltage is less ,anual 7. If the intake shutter solenoid valve half voltage is more than 7.

If seervice intake shutter solenoid valve full voltage is less than 7. If the intake shutter solenoid valve full voltage is more than 7. If the PCM detects that the input voltage for any cylinder is more than 4. If the voltage of the variable swirl control solenoid valve is high even if the variable swirl control solenoid valve is on, the PCM determines that there is a malfunction in the zervice swirl control solenoid valve control circuit.

If the voltage of the variable swirl control solenoid valve is low even if the variable swirl control solenoid valve is off, the PCM determines that there is a malfunction in the variable swirl control solenoid valve control system. If the PCM does not receive the injection confirmation signal for No. If the difference between the barometric pressure input from the barometric pressure sensor and the manifold absolute pressure is more than 75 mmHg, the PCM determines that there is a malfunction in the barometric pressure sensor.

Mazda 6 Workshop Manual

Go to Either or other condition appears: Step 10 for vehicles without immobilizer Go to the next step. Turn the engine switch to the ON position. Go to the appropriate DTC test. Communication error message is displayed: Is the DTC displayed? Inspect for the following: End Of Sie NO. Go Either or other condition appears: Go to appropriate DTC test. Is the engine overheating? Adjust the accelerator position sensor and the idle Are the accelerator position sensor and the idle switch correctly.

  CHARLES BUKOWSKI FACTOTUM ENGLISH PDF

Inspect the neutral switch adjustment. Does the wheel turn easily and smoothly? Inspect if the turbocharger turbine wheel is Replace the turbocharger. Is the fuel injector normal?

Repair or replace if necessary. Is the IDM normal? Inspect the timing belt for the following: Mxnual there any problem? Is any engine oil found inside the turbocharger Excessive amount of oil is found Does the engine run cold? Inspect the timing belt for followings: Perform the self-test function using the WDS or Make sure that all the hoses are securely connected in the proper position. Verify that the PID value is within specification. Start the engine and run it at idle speed.

Also See for 6 Owner’s manual – pages Manual – pages User manual – pages. Page of Go. Fuel and Emission Control. Heater 0209 Air Conditioner Systems. There are explanation given only for the sections. Table of Contents Add to my manuals Add. Chapters G Eneral Information Mazda 6 Owner’s Manual pages. Mazda 6 Manual pages. Automobile Mazda 6 Smart Start Manual 42 pages. Page 3 The contents of this manual, including drawings and specifications, are the latest available at the servkce of printing, and Mazda Motor Corporation reserves the right to change the vehicle designs and alter the contents of this manual without manuql and without incurring obligation.

Page 13 DTC P Page 14 DTC P Egr Valve Position Sensor Inspection 3. Page Yes Inspect suspected circuit or part or both according to the inspection results.

Dtc P WDS or equivalent. Dtc P — Less Than 0. Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page. To print the manual completely, please, download it. Don’t show me mnual message again. Got it, continue to print. Don’t have an account?